BCC Resins BC 8002
| 牌号 | BCC Resins BC 8002 |
| 厂家 | BCC Products Inc. |
| 分类 | PUR，未指定 |
| 介绍 | BCC Kwik Kast II is an advanced fast cast polyurethane tooling system. BC 8002 exhibits exceptionally low viscosity, low odor and is color contrasted for uniform mix. It features low exotherm and minimal shrinkage. Kwik Kast II cures hard, yet more durable resulting in less brittle parts. Uses include; tracing models core boxes, duplicating aids, patterns, prototypes, low temperature vacuum form tools, etc. Handling Properties: BCC's Kwik Kast II is a fast-setting, two part casting system which requires careful preparation prior to mixing parts A and B. Because Kwik Kast II contains components of high density there will be some separation at the bottom of each container. Using a paint shaker, jiffy mixer, or mixing spatula, re-suspension of the ingredients is easily accomplished. Precaution should be taken to prevent any moisture contamination from containers or utensils. It is recommended that the work area be well ventilated and normal cleanliness and safety rules be observed. Avoid prolonged exposure to vapors and contact with skin. Preparation of Mold Surface: Clean the surface from dust and possible presence of moisture. Apply BC 87 Parting Agent and polish to a uniform high gloss finish (usually 2-3 coats are recommended). For plaster or wood surfaces seal with PVC sealer to ensure complete absence of moisture, followed by 2-3 coats of 87 Parting Agent. Mixing and Pouring: Although not necessary, best results are obtained by evacuation of each component under 29 inches of vacuum which removes entrapped air prior to blending the two components. Pour weighed or measured amounts of Part A & B into a separate dry container by pouring Part A into Part B. Mix with a spatula or mechanical stirrer for 30-40 seconds for quart size batches or 40-50 seconds for gallon batches while avoiding air entrapment. Immediately pour mixed resin uninterrupted from a convenient height above the mold cavity. Clean your mixing tools by rinsing in an alcohol type solvent. Larger masses (2 feet or more) may be built up with successive pours. Castings may be demolded within 60-90 minutes but should be properly supported while "green". Under normal conditions, maximum hardness or cure will be achieved in 12-18 hours. |
在线客服: 
申请技术报告方式
可通过以下我公司客服QQ，索要技术报告
| 客服1： |
客服2： |
| BCC Products Inc. 产品展示 | 种类 |
|---|---|
| BCC Resins DP-11-75 | PUR，未指定 |
| BCC Resins MB3500 | PUR，未指定 |
| BCC Resins BC 8002 | PUR，未指定 |
| BCC Resins MB1150 | PUR，未指定 |
| BCC Resins BC 8010-2 | PUR，未指定 |
| BCC Resins MB1300 | PUR，未指定 |
| BCC Resins DP-11-90 | PUR，未指定 |
| BCC Resins BC 8005 | PUR，未指定 |
| BCC Resins BC 8163 | PUR，未指定 |
| BCC Resins DP-11-88 | PUR，未指定 |
订购说明
上海松翰塑化科技有限公司订货流程
【订购导引】
我司所销售所有产品均为原厂原包，均可提供相关资料报告（如：物性表，MSDS报告，UL报告，COA报告，SGS报告，FDA等）！
如您需要提前了解原料产品的相关性能或是需要原料产品的相关报告，请您通过电话或是客服QQ与我联系！
【物流说明】
自接到贵司订购单24小时内发货，珠三角，长三角，北京，天津均支持代收货款。货物送达后，请第一时间检查外包装，如发现物流过程中出现大量包装损坏及原料外漏的,请让物流人员出具证明并保存，并在24小时内与我司客服部取得联系。
【订购流程】
【退换货处理】
退货：
依照中华人民共和国消费者保护法规，在您收到货品7天内，若发现您收到的商品有瑕疵或损坏，您可以要求退货，请主动与本公
司联络，敝公司接到您的商品之后，会将您的购物金额全额退回。
换货：
若您收到的商品有瑕疵或损坏，请您于7天内与本公司联络，本公司有专人处理换货事宜。
我司所销售所有产品均为原厂原包，均可提供相关资料报告（如：物性表，MSDS报告，UL报告，COA报告，SGS报告，FDA等）！
如您需要提前了解原料产品的相关性能或是需要原料产品的相关报告，请您通过电话或是客服QQ与我联系！
【物流说明】
自接到贵司订购单24小时内发货，珠三角，长三角，北京，天津均支持代收货款。货物送达后，请第一时间检查外包装，如发现物流过程中出现大量包装损坏及原料外漏的,请让物流人员出具证明并保存，并在24小时内与我司客服部取得联系。
【订购流程】
【退换货处理】
退货：
依照中华人民共和国消费者保护法规，在您收到货品7天内，若发现您收到的商品有瑕疵或损坏，您可以要求退货，请主动与本公
司联络，敝公司接到您的商品之后，会将您的购物金额全额退回。
换货：
若您收到的商品有瑕疵或损坏，请您于7天内与本公司联络，本公司有专人处理换货事宜。
版权所有 © Shshsj.com All Rights Reserved