BCC Resins BC 8009
| 牌号 | BCC Resins BC 8009 |
| 厂家 | BCC Products Inc. |
| 分类 | PUR，未指定 |
| 介绍 | BCC Slo-Kast is a low viscosity, medium setting, easy to use casting material. This polyurethane system features extremely low shrinkage when properly cured. Unlike Kwik-Kast, BC 8009 offers the user longer working time (15 minutes for filling closed mold cavities and up to 25 minutes when casting into open molds). Slo-Kast is ideal for casting large sections without having to stage pour. Uses included; tracing models, core boxes, keller aids, patterns, core sticks, vacuum form tools, prototypes and display parts. Handling Properties: BCC's Slo-Kast is a moderately fast-setting, two part casting system (Part A & Part B). If settling from long storage has occurred, re-mix contents of each container on a mechanical paint shaker, jiffy mixer, or other suitable mixing equipment. Precaution should be taken to prevent any moisture contamination. Use dry equipment and containers and keep covered when not in use. It is recommended that the work area be well ventilated and normal cleanliness and safety rules be observed. Avoid prolonged exposure to vapors and contact with skin. Preparation of Mold Surface: Clean the surface from dust and possible presence of moisture. Apply BC 87 Parting Agent and polish to a uniform high gloss finish (usually 2-3 coats are recommended). For plaster or wood surfaces seal with PVC sealer to ensure complete absence of moisture followed by 2-3 coats of 87 Parting Agent. Mixing and Pouring: Pour weighed or measured amounts of Part A & B into a separate dry container by pouring Part A into Part B. Mix with a spatula or mechanical stirrer for 1 minute for quart size batches or 2 minutes for gallon batches. After mixing both parts allow container to sit undisturbed 3-4 minutes before pouring. This "induction time" will result in superior surface qualities of the cast piece. Pour mixed resin uninterrupted from a convenient height above the mold cavity to resist air bubble entrapment. Clean your mixing tools by rinsing in an alcohol type solvent. Larger masses (2 feet or more) may be built up with successive pours. Castings may be demolded in as little as 3.5-4 hours, but should be properly supported while "green". If partially cured casting is disturbed, a surface film may result. This is easily removed by wiping with mineral spirits or lacquer thinner. Under normal conditions, maximum hardness or cure will be achieved in 24-48 hours. |
在线客服: 
申请技术报告方式
可通过以下我公司客服QQ，索要技术报告
| 客服1： |
客服2： |
| BCC Products Inc. 产品展示 | 种类 |
|---|---|
| BCC Resins DP-11-88 | PUR，未指定 |
| BCC Resins BC 8645 | PUR，未指定 |
| BCC Resins BC 8400 | PUR，未指定 |
| BCC Resins MB1200 | PUR，未指定 |
| BCC Resins MB1150 | PUR，未指定 |
| BCC Resins BC 8165 | PUR，未指定 |
| BCC Resins BC 8086 | PUR，未指定 |
| BCC Resins DP-11-75 | PUR，未指定 |
| BCC Resins BC 8002 | PUR，未指定 |
| BCC Resins DP-11-90 | PUR，未指定 |
订购说明
上海松翰塑化科技有限公司订货流程
【订购导引】
我司所销售所有产品均为原厂原包，均可提供相关资料报告（如：物性表，MSDS报告，UL报告，COA报告，SGS报告，FDA等）！
如您需要提前了解原料产品的相关性能或是需要原料产品的相关报告，请您通过电话或是客服QQ与我联系！
【物流说明】
自接到贵司订购单24小时内发货，珠三角，长三角，北京，天津均支持代收货款。货物送达后，请第一时间检查外包装，如发现物流过程中出现大量包装损坏及原料外漏的,请让物流人员出具证明并保存，并在24小时内与我司客服部取得联系。
【订购流程】
【退换货处理】
退货：
依照中华人民共和国消费者保护法规，在您收到货品7天内，若发现您收到的商品有瑕疵或损坏，您可以要求退货，请主动与本公
司联络，敝公司接到您的商品之后，会将您的购物金额全额退回。
换货：
若您收到的商品有瑕疵或损坏，请您于7天内与本公司联络，本公司有专人处理换货事宜。
我司所销售所有产品均为原厂原包，均可提供相关资料报告（如：物性表，MSDS报告，UL报告，COA报告，SGS报告，FDA等）！
如您需要提前了解原料产品的相关性能或是需要原料产品的相关报告，请您通过电话或是客服QQ与我联系！
【物流说明】
自接到贵司订购单24小时内发货，珠三角，长三角，北京，天津均支持代收货款。货物送达后，请第一时间检查外包装，如发现物流过程中出现大量包装损坏及原料外漏的,请让物流人员出具证明并保存，并在24小时内与我司客服部取得联系。
【订购流程】
【退换货处理】
退货：
依照中华人民共和国消费者保护法规，在您收到货品7天内，若发现您收到的商品有瑕疵或损坏，您可以要求退货，请主动与本公
司联络，敝公司接到您的商品之后，会将您的购物金额全额退回。
换货：
若您收到的商品有瑕疵或损坏，请您于7天内与本公司联络，本公司有专人处理换货事宜。
版权所有 © Shshsj.com All Rights Reserved