Silanogran PV

牌号Silanogran PV
厂家Kettlitz-Chemie GmbH & Co. KG
分类Slip Agent / Lubricant / Mold Release / Processing Aid
介绍Silanogran PV is the 50% granular form of a trimethoxy-silyl-group containing low molecular polybutadiene (formerly Polyvest 25) on a mineral carrier. The pure liquid polymer is sticky and highly viscous. Our granular form provides easier handling, avoids inaccuracy and insecurity while dosing and incorporating the material into the rubber compound. The compressed granules of Silanogran PV are packed in low melting PE bags with a net content of 1 kg (standard packaging). If purchasing one pallet i. e. at least 600 kg net, special packagings of 0.5 up to 2.5 kg net according to customers' requirements can be supplied. By this means extra weight will not be necessary, which also results in better hygiene conditions because there will not be any direct contact with the material.

Properties and Application

The active substance of Silanogran PV is a low molecular polybutadiene containing silane groups which react by means of their alcoxy groups (trimethoxy groups) and the silanol-groups-containing surfaces of silica and silicate fillers. The unsaturated polymer chains of Silanogran PV are integrated in the rubber matrix during vulcanization. Highest effectiveness is achieved in EPDM compounds containing silicates with a laminar structure (e. g. Sillitin, talc, mica and some grades of clay), but also in any other vulcanized rubber an improvement of the physical properties will be noticed. Sialnogran PV can be used in sulfur and peroxide cured compounds. Silanogran PV is usually dosed between 1-6 weight percent calculated on silica fillers. A special mixing sequence does not have to be observed. Silanogran PV can be incorporated in internal mixers and on mills as well.

The application of Silanogran PV results in an improvement of the curing properties as stated below:

  • Shorter curing time at equal scorch time
  • Better process ability of the uncured compounds by lowering Mooney Viscosity
  • Increase of tensile strength, modulus and tear resistance
  • Improvement of Compression Set
  • Decrease of abrasion
  • Minimized water absorption i. e. better electrical properties of cable compounds
  • Increase of dynamic proeprties
在线客服:  点击这里给我发消息 点击这里给我发消息 上海松翰塑胶
申请技术报告方式

可通过以下我公司客服QQ,索要技术报告

客服1:点击这里给我发消息 客服2:点击这里给我发消息
Kettlitz-Chemie GmbH & Co. KG 产品展示 种类
Antitack BTO-33 Slip Agent / Lubricant / Mold Release / Processing Aid
Mediaplast 60 Slip Agent / Lubricant / Mold Release / Processing Aid
Silanogran Silanogran SI-69/GR 70 Slip Agent / Lubricant / Mold Release / Processing Aid
Antitack BTO-30 Slip Agent / Lubricant / Mold Release / Processing Aid
Mediaplast AT Slip Agent / Lubricant / Mold Release / Processing Aid
Activin NT Slip Agent / Lubricant / Mold Release / Processing Aid
Antitack BTO-7 Slip Agent / Lubricant / Mold Release / Processing Aid
TAIC 70 Slip Agent / Lubricant / Mold Release / Processing Aid
Silanogran PV Slip Agent / Lubricant / Mold Release / Processing Aid
Mediaplast EV/F Slip Agent / Lubricant / Mold Release / Processing Aid

订购说明

上海松翰塑化科技有限公司订货流程

【订购导引】
       我司所销售所有产品均为原厂原包,均可提供相关资料报告(如:物性表,MSDS报告,UL报告,COA报告,SGS报告,FDA等)!
       如您需要提前了解原料产品的相关性能或是需要原料产品的相关报告,请您通过电话或是客服QQ与我联系!

【物流说明】
       自接到贵司订购单24小时内发货,珠三角,长三角,北京,天津均支持代收货款。货物送达后,请第一时间检查外包装,如发现物流过程中出现大量包装损坏及原料外漏的,请让物流人员出具证明并保存,并在24小时内与我司客服部取得联系。


【订购流程】
订货流程



【退换货处理】
退货:
依照中华人民共和国消费者保护法规,在您收到货品7天内,若发现您收到的商品有瑕疵或损坏,您可以要求退货,请主动与本公
司联络,敝公司接到您的商品之后,会将您的购物金额全额退回。

换货:
若您收到的商品有瑕疵或损坏,请您于7天内与本公司联络,本公司有专人处理换货事宜。
版权所有 © Shshsj.com All Rights Reserved